DC 24V Power PLC Transistor Module , PLC Negative Control DC
Amplifier Board
1 , the load voltage, current type is different
Load type: Transistors can only carry DC loads, while relays can
have both AC and DC loads.
Current: Transistor Current 0.2A-0.3A, Relay 2A.
Voltage: The transistor can be connected to 24V DC (generally the
maximum is about 30V DC, and the relay can be connected to DC 24V
or AC 220V.
2, different load capacity
The ability of a transistor to carry a load is less than the
ability of a relay to carry a load. When using a transistor, it is
sometimes necessary to add other things to drive large loads (such
as relays, solid state relays, etc.).
3, the transistor overload capacity is less than the ability of the
relay overload
In general, when there is a large inrush current (for example,
light bulbs, inductive loads, etc.), the transistor has less
overload capacity and needs to be derated more.
4, transistor response speed faster than the relay
The principle of relay output type is that the CPU drives the relay
coil to make the contacts pull in and make the external power
supply drive the external load through the closed contacts. The
open circuit leakage current is zero and the response time is slow
(about 10ms).
Transistor output type principle is the CPU through the optical
coupling to make the transistor off, to control the external DC
load, the response time is fast (about 0.2ms or even less).
Transistor output is generally used for high-speed output, such as
servo/stepping, etc., for output with high operating frequency:
such as temperature PID control, mainly used in stepping motor
control, servo control, and solenoid valve control (high valve
operating frequency ).
Transistors are mainly used for positioning control. The output of
the crystal is used to emit pulses. The relay cannot be pulsed and
it cannot be positioned. If the relay is used to control the
positioning servo or stepping, the positioning module must be
added, which is not economical. With a single transistor output,
servos can be controlled.
5. In the rated working condition, the relay has life cycle times,
and the transistor has only aging and no limit on the number of
uses.
Because the relay is a mechanical component, it has a long
operating life. The transistor is an electronic component. Only the
aging is used, and the number of uses is not limited. The number of
switches per minute of the relay is also limited, while the
transistor is not.
6, the transistor output price slightly more expensive.
Relay output:
AC ------ AC (normal AC 220V) power supply (L1 N)
DC ------ DC (input)
RLY ------- Relay output (output)
Transistor output:
DC ------ DC (normal 24V DC) power supply (L+M)
DC ------(input)
DC ------ (output) such as PLC 224 XP CN DC/DC/DC
♦ Features
-- Standard DIN rain mounted
-- Status indication for each input
-- Special circuit for self test and anti-interference
-- High quality MOSFET with large load and excellent stability
♦ Typical Applications
• Micro-controller • PLC control • Servo System
• Electro-magnetic valve • DC Motors
• Home intelligent control
♦ Technical data
| Model | JR-XJ |
| Output type | MOSFET(PNP OUT) |
| I/O points | 4CH,6CH,8CH,12CH,16CH |
| Input signal | NPN/PNP |
| Input voltage | DC24V |
| Output voltage | DC 12-24V |
| Output Contacts | 1NO |
| Contact capacity(resistive) | 5A 24VDC |
| Operation voltage/Release voltage | >5VDC/<1.5VDC |
| Operation time/Release time | <10ms/<10ms |
| Switching frequency | ≥5kHz |
| Dimensions(WxH) | 87×46mm |
| Mounting | DIN rail |
